Bandini formula 3

The 'Bandini formula three' is a 'car racing produced by 1954 1958 by the company Bandini Cars Forlì.

This type, produced at the same 'two-seater sports was born in order to participate in the category 'race until 750 cm ³ "engine capacity which provided for the exclusive use of car car. This category gave birth to Formula Junior first, and the current formula three onwards; ereditiere purpose propedeutiche for future samples of specialties.

The characteristics that make importantformula three (single-seater race 750)from the point of view of the historical Bandini are basically two: the unprecedented postponement of box ' transmission shaft and testing of disc brakes on four wheels.

The advantages of the latter were mainly limited solely to lower unsprung masses as the study of materials of seals of friction had not yet allow quell'evoluzione that today poses this choice as a solution required the cars allocated to the races.

photos rear, highlighting disc brakes and the differential

The box to postpone the transmission instead, a system was also used in subsequent formulajunior it offered a double advantage: making rapid replacement of two gears that determine the final drive ratio (allowing a rapid adaptation to the circuit) and, simultaneously, abbassava significantly the transmission shaft that conditioned to turn the position of the seat of the pilot. This allowed a lowering of CG with the consequent improvement of road holding total of the car.

The racing debut occurred on July 1954 to the third edition of "Cup Louis Arcangeli," disputatasi on the circuit Forli.

Ilario Bandini laying next to a formula Bandini 3

The same manufacturer Ilario Bandini, classified in second place in the race reserved for "single way up to 750 cm ³" valid for the Italian championship.

The Frame

The frame, weighs just 16 kilograms

The chassis keeps the characteristics, materials and design, used for torpedotwo-seater sports, but the size, necessarily lower a car, make it possible to further cut the weight that descends so only 16 kg.

The instrumentation only shows: r engine, water temperature and pressure oil

• Structure and material: a tower pipe section elliptical, steel special derivation aeronautics; patent No. 499843
• Suspensions:
  • Front: Independent, triangles overlapping with shock hydraulic telescopic tilted and springs cylindrical helical coaxial; bar Account
  • Rear: a bridge with two rigid leaf spring semiellittiche longitudinal and shock hydraulic vertical telescopic
• Braking system:
  • Service: hydraulics, drum front and rear, as an alternative hydraulic disc on four wheels
  • Parking: not found
• Steering: a worm
• Guide: single, central location
• Wheels: ray Borrani
• Tank: 25 Litres
• Transmission: transmission shaft with joints cardanici, differential central position reversed and box with quick change of relations (6 reports available) and the semiassi rear
• Weight: bare chassis 16 kg
• Weight total: 300 kg

The Engines

The engine Bandini first series

The three Bandiniformulaused the same engines which avvalsero the two-seater sports the same period: Bandini-Crosley first and second series, although the duration of lesser races for single-seater allowed the use of modifications and adjustments "pushes" as an increase in the compression ratio or the use of rods alloy d 'aluminium.

• Positioning: forward longitudinal, 4-cylinder in-line
• Materials and particularity: base 5 media bench and league cup d 'aluminium of 5 litres capacity, head in aluminium [[bialbero] ] Gear with 8 valves inclined, chrome cylinders dismantled in monoblock iron.
• Bore: 63.5 mm
• Running: 59 mm
• Capacity: 747 cm ³
• Compression ratio: 11.2:1
• Power: 2 Weber carburetors double body 35DCO3 horizontal or vertical
• Power: 66 to 73 hp 9000 rpm
• Lubricate: Carter with wet gear pump and filter external wire mesh
• Cooling: forced liquid with centrifugal pump controlled by pulley and belt, radiator tilted all'avantreno
• Currency and clutch: 4 + marches RM, clutch monodisco dry
• Ignition and electrical equipment: coil and distributor switch on the head, battery 12 V and generator

The engine Bandini second series with carburettors vertical

The Bodywork

The bodywork in aluminium, made the Bandini were of two types; different especially on the front: a very similar to torpedo two-seater, with grid elements horizontal and vertical elliptical high and very rounded and the other lower and spigolosa with the air-intake front almost a semicircle. Both solutions were not welded to the body car but screwed to it, so as to enable the interchangeability as well as add convenience in the event of operations in the engine compartment or contacts to tender. As the front, the tail and side panels of the engine compartment were easily dismantled. They have openings in gills of sharks in the two positions in relation to the role: the air fresh or sfoghi of warm air). Their position reveals the use of different carburettors (horizontal or vertical). Almost always present instead sfoghi large rectangular body on the car, between the engine compartment and the cockpit, where the body is deeply dug. To protect aerodynamics of the pilot, only a small "slide" or a windshield that wraps the whole but for a few centimeters in height. The tail, very short and appuntita closed slightly above the rear axle at a point where confluisce also fin-rollbar, originatasi immediately behind the pilot.

== == Related Items

• Bandini Cars
• Ilario Bandini